Thursday, October 13, 2022

Rock Island GP35 #307

#4

Following close on the heels of the #323 is #307, I was working on this one right after I got the #323 done and was waiting on the chips to arrive.

Pretty much the same as the #323 except it's Maroon and Yellow.  Nothing special about this one, just the typical scheme on a GP35.

The only thing about the unit, some of the images that I found of #307 shown it to be quite dusty which I tried to portray by adding dust powders to the trucks and fuel tank.  I debated about what color to paint them with?

Do I start with a gray (similar to what the Red and Yellow units get painted?) and then darken them down with washes and powders, or do I start with painting them black and trying to lighten them up with dust powders?

I decided to start with black and add the dust.

It took several layers of Pan Pastels and misted with light coats of Dullcote to achieve the dusty look but it also now looks as if I started with gray for the trucks and fuel tank.






Here's a shot of the speed lettered units on the bridge.


Four down, three to go...




Tuesday, October 11, 2022

Rock Island GP35 #323

Yet another GP35 joins the fleet, this time it's #323.





I did take the liberties of adding a few rust spots to cab.


It's the only GP35 that wore the Red and Yellow scheme and along the way I realized that it had a couple of oddities with the scheme.

The first thing I noticed was the lack of the nose herald, the second thing were the faces of the steps below the cab.  Normally on this scheme and the maroon and Yellow scheme these faces were Maroon or Red.  The third thing was the bottoms of the end handrails, at some point the original silver was painted white.




Thanks to Jim Merrick for the explanation of the white paint on the handrails.
I'm gonna repost it on the page so that it's not lost in the comments.

Jim MerrickOctober 11, 2022 at 9:54 AM

Explanation on the white steps and rails: That last photo is from the late '70s, after the red paint went away and all the shop had was white or blue. The last several years of ops saw a LOT of white touch-up happen on red or maroon units. Up until somewhere around 1977 or so, the touch-ups were done in the "correct" matching colors. Touch-ups happen a lot, especially on steps and pilots and plows and nose/cab front, as those are high-wear areas.


Wednesday, September 21, 2022

Rock Island GP35 #301

Tonight, Rock Island GP35 #301 joins the fleet.

I never knew much about this Maroon Dip scheme and wasn't aware that it was ever applied to the GP35's until I started researching paint schemes for the 35's?  It's a Plain Jane scheme but I like the simplicity of it.  I know a lot of the U25B's wore it.

I weathered it pretty much the same way that I did the last GP35 and the U33B's so I won't bore you with the details.

 






For comparison with the #325



And this time a quick video of the pair crossing the bridge.






Tuesday, September 13, 2022

Rock Island GP35 #325

One down, six to go.

I applied the finishing touches on the first of the Rock Island GP35's.  I originally did this loco a number of years ago and was not planning to redo it until I pulled it out to give it a look over.  There were several things that I did wrong back then because I wasn't very knowledgeable and I really didn't have that many images available, unlike there is today thanks to the internet and Facebook.  Not to mention what I've learned with weathering and some of the newer mediums we have to work with today.

Like I did with the U33B's recently, I painted it with TCP Rock Island Maroon, Micro Scale decals, and the numberboards by Shell Scale decals.  The weathering was done using mainly Pan Pastels and the oil and fuel leaks were done with Tamiya Black panel liner.  Plus I installed all four marker lights this time since I have enough to last me now.

The way the glazing sets (specifically the headlights) in these Atlas units are designed, I didn't have to replace them with Fiber Optics like I did on the U33B's.  In this case all I needed to was to glue the 804 LEDs directly the headlight glazing.  While it's not quite as bright as the Fiber Optics in the U33B's, it's a hell of a lot brighter than what it is with just relying on the surface mount LED on the DCC board.

If you look at the two pictures of both ends of the loco you can see how dim the rear lights are compared to the front light since I didn't add an LED to the rear.  Why didn't I add an LED to the rear light you ask?  I normally don't run my locos long hood forward so I didn't waste the time and effort.

Anyway enough rambling... 






Here's a side by side of the original on the left and the new on  the right.

The old one was painted with Floquil Rock Island Maroon which is a bit lighter.  The TCP is a much richer Maroon and closer to the factory color.



After as much research that I've done recently with the U33B's and these GP35's, along with all the new available photos that I've found online, the one thing I've come to realize about most of the Rock Island locomotives that were photographed in the final years of operations is that most weren't Rust Buckets. They were more grimey than rusty.  This is why the newer GP35 is a little darker this time around.

Several of the GP35's that I have planned will not be as dark or grimey but will hopefully look a lot more sun bleached and faded.  The weathering was quite diverse in the final years of the Rock.  This is what has drawn me to model this road.

 



Thursday, September 1, 2022

1mm Jewels for marker lights

Years ago, back in the late 80's I bet, I ran across some little tiny jewels at the local hobby shop.

They were brought to my attention as a friend used them for marker lights on his HO locos for marker lights.  Intrigued, I took a closer look at them and saw that they had them as small as 1mm.

They also came in three colors: Red, Green and Clear.  So I picked up a pack of the clear 1mm's to play around with.  



They looked to be just about the right size, maybe a tad too big.  Feeling gutsy I took a sharp #17 exacto blade and shaved off the molded part of the marker light (the part that was supposed to the lens) and left the base.  Then I took a #56 carbide drill bit and slowly started to drill in the middle of the remaining base, just enough to where the little jewel would sit into the hole.  The trick was to not drill clear through, so I twisted the bit a few times and checked the fit.

Since the drill bit had a slight angle on the tip, like most do, it left a nice little divot just big enough that the 1mm jewel dropped right in.  Then using a toothpick I applied a tiny drop of CA glue and carefully laid the jewel in place.  Viola!  A nice looking marker light.  It wasn't lit, but it reflected the ambient light just enough to sparkle and look like the light was on.

I've been doing this for years but recently I noticed I was getting low on them and knowing they'd been out of stock/production forever.  I was beginning to think that I wouldn't ever find any again.

But while snooping on the nifty little tool we have at our disposal these days: the Internet, I started in one night looking for "1mm Jewels".  Not much luck, so I kept refining my searches.  Finally I found some that looked similar but were too big.  These were Rhinestones.

So I refined my search and bingo!  I found some on Amazon but they were still a little too big.  I finally found some 1mm's on a site from the UK called mybeadsfindings.

I wound up buying two 5 packs of them, each 5 pack had roughly 1440 stones, so I wound up with almost 3000 marker lights for about $15 with shipping from the UK.  I don't think I'll ever have to worry about running out again?  Unless I misplace them...

I apologize for the fuzzy images, my new phone doesn't do close-ups as well as my older iPhone 11.



I drill out the molded in marker lenses.


Then apply a small dab of CA glue to the finished model.


They might be a tad too large but they sure look good when the light hits them just right.



Monday, August 29, 2022

Rock Island GP35's

With the U33B project wrapped up I had planned to get back to the layout and work on a couple areas.  But I just don't seem to have the interest built up enough yet.  When I was prepping the U33B's I also laid aside five GP35's so I could them added to the fleet.

So last night I got them stripped down and ready to attack.


After taking the image I got to thinking about the two GP35's that I painted and weathered years ago.  I was never really fond of them after what I've been doing with weathering over the last several years and what I've learned.  When I dug them out last night and took a long look at them, I decided to strip down two more GP35's and add them to the "To-Do" list, so now I've got 5 new ones and two re-do's on the bench.  This will also allow me to correct one mistake that I did to them before I knew what some of the correct details parts were.

One will be the only Rock ISland GP35 to wear the 70's distinctive Red and Yellow livery, the rest will be painted in several different versions of the solid Maroon dip and the Maroon and Yellow schemes.  



Friday, August 26, 2022

Let's follow train #34 SB from Biddle yard.

Today we're going to follow train #34 SB from Biddle yard in Little Rock, AR. south to Whitewater Creek, just north of Fordyce, AR.  Today’s power has 5 U33B's.  
Although 16,500 hp might be a bit of overkill for this train, it sure is neat to see.



Monday, August 22, 2022

Rock Island U33B #273

Put the wraps on my fifth and final U33B.

This time I actually had the presence of mind to take a couple of "Before" pics this time.



As I've done with the previous four, all the weathering was done with several Pan Pastel colors.  In this case I used Raw umber tint to fade the paint, Raw Umber to tone down the fade so it was so stark and then Black for the soot.  I also used the same colors on the trucks and fuel tank.

I did not use the Tamiya Black Panel Liner this time for oil and fuel spills, but I may go back and add a little?




 

With this project wrapped up, I'm not sure what I plan to do next?  While I do have 5 GP35's on deck next, I may start working on the next scene on the layout.  This would be one of two things:  1) The Ouachita River Bridge scene (the bridge in the images above)  or 2) Reworking all the tracks in the town of El Dorado.  Basically removing most of the existing yard tracks and the A/D tracks.

One thing I do plan to do this fall is to start listing a lot of the extra stuff that I don't need anymore: Rolling Stock, Locos and some building kits.  Since eBay started with their nonsense of the $600 limit, I plan to start listing stuff on several of the Forums and probably Facebook.